Home  <  Dental Professional  <  KIT & Tools  <  Surgical Tools
Type Extra Short Short Long Application
L 8 10.3 15.5 -
0.5Slot - ASD05SH ASD05LH -
0.9Hex AHD09MSH AHD09SH AHD09LH Cover Screw
(US Mini)
1.2Hex 2.0 AHD12SH AHD12LH Healing Abutment, UCLA,
Cemented Abutment Screw,
Mount Screw
2.0 Int. Hex - IHD20H Esthetic Abutment Screw
Regular Esthetic-low
Abutment Screw, Standard
2.7 Int. Hex - IHD27H Wide Esthetic-low Abutment
Screw
  • ㆍPacking Unit : each part
  • ㆍManual driver
  • ㆍTip holding function (note: excluding Int. Hex Type)
  • ㆍInt. Hex L is 11
Type Short Long Extra Long Application
L(Slot) 7 11 15.5 -
0.5Slot 5 9 15  
0.9Hex AMSD05S AMSD05L   -
0.9Hex AMSD09S AMSD09L   Cover Screw (US Mini)
1.2Hex AMSD12S AMSD12L AMSD12E Healing Abutment, UCLA, Cemented
Abutment Screw, Mount Screw
2.0 Int. Hex EIHD20 Esthetic Abutment Screw Regular
Esthetic-low Abutment Screw,
Standard
2.7 Int. Hex EIHD27 Wide Esthetic-low Abutment Screw
  • ㆍPacking Unit : each part
  • ㆍManual driver
  • ㆍTip holding function (note: excluding Int. Hex Type)
  • ㆍInt. Hex L is 8
Type Short Long Extra Long Application
L 9.5 15 25 -
0.5Slot TRSD05S TRSD05L TRSD05E -
0.9Hex TRHD09S TRHD09L   Cover Screw(US Mini)
1.2Hex TRHD12S TRHD12L TRHD12E Healing Abutment,
UCLA,Cemented Abutment
Screw, Mount Screw
2.0lnt. Hex TIHD20S TIHD20L - Healing Abutment, UCLA, Cemented
Abutment Screw, Mount Screw
2.7Int. Hex TIHD20S TIHD20L - Standard/ Esthetic Abutment
Screw, Regular Esthetic-low
Abutment Screw
2.7 Int. Hex   TIHD27   Wide Esthetic-low Abutment Screw
  • ㆍPacking Unit : each part
  • ㆍDriver for torque wrench connection
  • ㆍNo tip holding function
  • ㆍFracture strength: 62Ncm
  • ㆍRecommended torque should be observed. Caution: Fracture occurs, in case excessive torque is applied.
  • ㆍWhen applying torque, check that the screw hex is completely installed. Application of torque with imperfect installation may result in a fracture at the strength under fracture strength.
  • ㆍTorque should be applied vertically. (Do not tilt the set.)
  • ㆍIf the tip is bent due to the use for a long time or excessive torque, replace it.
Code AORD
  • ㆍPacking Unit: each part
  • ㆍSpecial-purpose driver for the O-ring abutment
Spec. Mini Regular
Abutment D(ø) ø4.8 ø4.0 ø4.5 ø4.5 ø6.0
Short ORDMS ORD45S ORDRS ORDWS
Long ORDML ORD45L ORDRL ORDWL
  • ㆍPacking Unit: each part
  • ㆍSpecial-purpose driver for rigid abutment
  • ㆍTightening torque : 30Ncm
Platform(ø) Regular Wide
Square Round Square Round
Short SDSS SDRS SD60S -
Long SDSL SDRL - -
  • ㆍPacking Unit: each part
  • ㆍDriver for Solid abutment
  • ㆍThe triangle mark is used by aligning with the abutment groove
  • ㆍTightening torque : 30Ncm
Platform(ø) Regular Wide
Square Round Square Round
Short ESDSS ESDRS ESD60S -
Long ESDSL ESDRL - -
  • ㆍPacking Unit: each part
  • ㆍDriver for Solid abutment
  • ㆍThe triangle mark is used by aligning with the abutment groove
  • ㆍTightening torque : 30Ncm
Square Round
Short ODSS ODRS
Long ODSL ODRL
  • ㆍPacking Unit : each part
  • ㆍDriver for Octa abutment
  • ㆍTightening torque : 30Ncm
Type Short Long
L 10 15
1.2 Hex OTH12S -
Rigid ø4.0 OTR40S OTR40L
Rigid ø4.5 OTR45S OTR45L
Rigid ø5.0 OTR50S OTR50L
Rigid ø6.0 OTR60S OTR60L
Solid OTS48S OTS48L
Excellent Solid OTE48S OTE48L
  • ㆍPacking Unit : each part
  • ㆍDriver for OSSTEM Torque
  • ㆍThe triangle mark is used by aligning with the abutment groove of section
  • ㆍTightening torque : 30Ncm(except 1.2 Hex Type)
  • ㆍSolid and Excellent Solid Driver are compatible with 4.8 exclusively.
  • ㆍImpossibility of connection with general hand piece
  • ㆍ1.2Hex L(Tip length) is 5.
  Mini Regular
Short GIPAP-3016A GIPAP-3516A
  • ㆍPacking Unit : each part
  • ㆍAfter GS,TS NoMount driver, confirmation path and measurement gingival height
  • ㆍFor mini : Yellow
  • ㆍFor Regular : Green
Code ORC
  • ㆍPacking Unit: each part
  • ㆍConnector used for connecting the driver for square torque to the round torque wrench
Code TIDHC
  • ㆍPacking Unit: each part
  • ㆍUse by connecting with a torque driver
Code ODSD
  • ㆍPacking Unit: each part
  • ㆍUse to adjust the retention force of Dalbo plus Attachment
Code FRSC
  • ㆍPacking Unit: each part
  • ㆍUse to remove the lip inside the casting body upon the casting of plastic copings
  • ㆍHow to use reamer
  • A.Choose a reamer tip as same size as abutment and then connect the casting burm-out Cylinder.
  • B.Hold the casting body and rotate reamer bite with consistent force
  • C.Do reaming until cutting does not occur any longer
Code FRBC
  • ㆍPacking Unit: each part
  • ㆍTiN coating improves anti-corrosion and wear resistance
Abutment D(ø) ø4.0 ø4.5 ø5.0 ø6.0
Code GSRFRT400 GSRFRT450 GSRFRT500 GSRFRT600
  • ㆍPacking Unit : each part
  • ㆍWhen fabricating the prosthesis using a Rigid plastic coping, it is used for margin contact adjustment.
Diameter(ø) ø4.0 ø5.0
Solid FRTS480 FRTS600
Excellent Solid FRTE480 FRTE600
  • ㆍPacking Unit : each part
  • ㆍCombined use of Solid ø6.0 and Excellent Solid ø4.8